Ubiquiti UDM - BT Community
网页2022年1月9日 · Re: Ubiquiti UDM. @tomhumph97 I ditched the SM2 as soon as possible. Unless you need the digital phone I cannot think of a good reason to keep the SH2 except for troubleshooting any service problem. My UDM is connected directly to the ONT with Orbi servicing the Wi-Fi because I didn’t want to run cables just now.
Ubiquiti Dream Machine Pro With BT FTTP
网页2020年12月1日 · Re: Ubiquiti Dream Machine Pro With BT FTTP. Ok thanks - I want to set the dream machine up first in my office with wireless points before transferring it over to the actual cabinet. When this is set up and I unplug it all temporarily for the install into rack can I use my BT home hub straight away again (as I need internet during this ‘down ...
Ubiquiti and BT Hub 2 for digital voice
网页2022年7月5日 · Re: Ubiquiti and BT Hub 2 for digital voice. There are 2 ways to connect things together, LAN - WAN or LAN - LAN. If you connect LAN - LAN you will not be double natting, the first device (BT Hub) will be doing all the routing and natting the second device (Ubiquiti) will just act as a wireless access point. If you connect LAN - WAN, you will ...
FTTP IPv6 UniFi Dream Machine Pro - BT Community
网页2023年7月11日 · Re: FTTP IPv6 UniFi Dream Machine Pro. While I don't have the UnifI Dream Machine Pro, the settings for the WAN should be pretty simple. Connection type: Native. Interface: PPP. DHCP-PD (or DHCP64): enabled. WAN Prefix length: 56. Auto-Config: Stateless will generate random IPv6 addresses within your allocation while …
Solved: Ubiquiti USG with FTTP using the Smart Hub 2 (beca... - BT ...
网页2021年8月29日 · Re: Ubiquiti USG with FTTP using the Smart Hub 2 (because of Digital Voice) Okay so the USG LAN by default gets allocated 192.168.1.1 and I should manually set the USG WAN to 192.168.1.10. I would have thought the SuperHub would have automatically given the WAN port an IP, it only seems to have the LAN port registered.
Fibre900 Speeds with Ubiquiti Dream Machine - BT Community
网页2020年6月27日 · Re: Fibre900 Speeds with Ubiquiti Dream Machine. Hi, I have that exact set up. Before and after the UDM, I'm hitting the same speeds c.800 - 840Mbps. Switching intrusion detection on made no difference - I think the …
Solved: Using BT Fibre FTTP with UniFi Security Gateway (U... - BT ...
网页2020年6月27日 · 2. Power cycle the ONT by powering it down for at least 5mins. 3. Connect the cable from the active port on the ONT to the WAN port of the USG. 4. Use the common user name [email protected] and password (If required, but can be anything) BT In the USG setup with a PPPOE connection.
G.Fast MT992 modem with Ubiquiti UniFi Dream Machi ... - BT …
网页2020年11月27日 · Re: G.Fast MT992 modem with Ubiquiti UniFi Dream Machine All-in-One Router. Small update, I have the MT922 working with a Watchguard T30. The external interface is configured for PPoE with username [email protected] and password BT. No other configuration needed.
Solved: ONT to Dream Machine Pro - BT Community
网页2023年3月16日 · Re: ONT to Dream Machine Pro. Because if the connection is 1gb and the lan is 1gb then the lan can be restricting the internet connection due to other network traffic - as tested currently. And I may well want to use the rj45 internet connection on the udm for another isp. so yes, I deem it necessary. Thanks in advance.
Full Fibre 900 with UniFi Dream Machine Pro (UDMP)
网页2020年6月14日 · So, my setup is as follows: Openreach ONT Modem > USG Pro 4 > UniFi Switch > Multiple Access Points. When plugging in the MacBook directly to the ONT Modem and configuring the POE on the MacBook, I saw speeds as follow: Fast.com: 1 Gbps (D) and 120 Mbps (U) Speedtest.net: 880 Mbps - 910 Mbps and 110 Mbps -120 Mbps (U)