What's your experience with Unifi USG? : r/Ubiquiti - Reddit
网页2023年9月30日 · I've been using Unifi for about 4 years, with using USG for about 2 years. For the last couple of months, it started to drive me nuts. I have two networks (wire and 4g), but I read through the forums and it's confirmed that the failover switch has been broken for 4 years. I have already accepted that, but when I went back to the old UI I ...
USG in 2023...? : r/Ubiquiti - Reddit
网页The USG has some IDS/IPS functionality, but if you turn it on, it can seriously limit throughput. When I was at an MSP, we had many clients who used the Unifi APs and either the Cloud Controller or software controller on like a VM, but then in place of the USG, they used all sorts of different routers.
Speed is being limited on my Unifi network to 100Mbps for all
网页2022年1月14日 · Have 250Mbps fiber, everything wired Cat6, testing at 250Mbps on a laptop plugged right into the modem. Plug that same cord into my USG and from the USG to my Unifi POE switch and every device connected to that switch (including my wireless AP) is testing at 100Mbps on the dot every time, never a single bit less or more.
PSA If you are still using a USG-3P. : r/Ubiquiti - Reddit
网页PSA If you are still using a USG-3P. Quality Shitpost. I've seen a handful of USG-3Ps "die" in the past few months and every time the box itself was fine but the power supply had failed. Swapping in a good PS was all it took to get things going again. You can order replacement from the usual places for $15 or less.
My experience upgrading a USG to a Cloud Gateway Ultra
网页This is a place to discuss all of Ubiquiti's products, such as the EdgeRouter, UniFi, AirFiber, etc. My experience upgrading a USG to a Cloud Gateway Ultra. Hi, I just thought I would report my experience with this upgrade, since I did a lot of research here before giving it a try. I had a USG, Gen1 Cloud Key, and a Flex mini switch that I was ...
Best way to configure USG and Adguard Home - Reddit
网页2020年6月9日 · Pihole (Rpi3) DNS = Unifi USG local network address 2. Secondary DNS is what I personally do with my Pihole setup - in case the Rpi3 SD card fails so I don't lose my whole network (I run the controller on it also). But setting it to anything other than the Pihole server allows ads in at some level, since it's down to whichever responds first.
Local DNS on the USG - confused : r/Ubiquiti - Reddit
网页2021年7月17日 · Unifi's ability to manage external DNS is limited if not non-existent. But your setup sounds like something you should be able to do "simpler": Tell all your clients to use DNS on your USG. Have your USG forward to …
How to enable LAN2 interface on USG? : r/Ubiquiti - Reddit
网页2020年12月12日 · In the controller software using classic settings; Network. Create New Network. For Network Group choose LAN2. Hello! Thanks for posting on r/Ubiquiti! This subreddit is here to provide unofficial technical support to people who use or want to dive into the world of Ubiquiti products.
How to flash and recover Unifi Security Gateway (USG-3)
网页2021年1月13日 · Re-flashing worked! Process overview: Physically open USG, remove USB and flash it with outdated firmware, connect USG to internet, ssh into USG, update firmware through CLI. Extract the bz2 file with 7zip or similar. Unplug the USG and remove the rubber feet from the USG. Unscrew the screws beneath the rubber feet.
Help please! How to replace a USG with a new one? : r/Ubiquiti
网页2021年6月29日 · Login to the controller. Have the controller forget the old USG. Physically replace the old USG with the new one. Use the controller to adopt the new USG. The issue is getting onto your controller. If you use your phone to go to unifi.ui.com and look at the controllers page, then the internal IP address of your controller might be listed in the ...